Related stories. Possible solutions include, dedicated wireless adapters for each device, or installing Ethernet jacks. Unfortunately, those options can get expensive and each has its unique drawbacks. Another option is using a wireless bridge.
A wireless bridge connects two wired networks together over Wi-Fi. The wireless bridge acts as a client, logging in to the primary router and getting an Internet connection, which it passes on to the devices connected to its LAN Jacks. You can buy a dedicated wireless bridge, but if you have an old router lying around, you might be able to convert it into a wireless bridge using DD-WRT. A wireless bridge connects two wired networks together over Wi-Fi. Screenshot by Ed Rhee/CNET. Is free Linux-based firmware for routers that replaces the router's factory firmware.
It can breathe new life into an old router, giving it enhanced performance and new features. One of the features of DD-WRT is the ability to switch the router's function to a wireless bridge. This tutorial, based on the, will go over how to configure DD-WRT for use as a wireless bridge (client bridge mode), using a Linksys WRT54G router as an example. The process is fairly straightforward but will require some time and patience to complete.
In the steps below, primary router refers to the main router that you'll connect to, while bridge router refers to the router you're configuring as a client bridge. Step 1: Check the to see if your router is supported. If your router isn't supported, keep an eye out at for router deals. Rick Broida recently found a. Step 2: If your router is supported, you'll see it listed in the database and it'll include links to the firmware. It may also include device-specific directions on how to install DD-WRT, but you'll want to read over the as well.
In some cases, you'll need to install a firmware prep, prior to installing the actual DD-WRT firmware. It's possible to brick your router during installation if not performed correctly, so read the directions carefully and follow each step as noted.
Step 3: Once you've successfully installed DD-WRT, perform a hard reset on the router. This usually involves holding a reset button/pin for 30 seconds or until you see the router's lights flashing. Refer to your router's user manual to figure out the exact method for a hard reset. Step 4: Connect an Ethernet cable from your computer to one of the LAN jacks on the bridge router, then set a static IP address on your computer. Use something like 192.168.1.10, so you'll be on the same subnet as the bridge router, which will have an IP address of 192.168.1.1.
Step 5: Open a Web browser and enter 192.168.1.1 in the address bar. The DD-WRT Web interface will appear and you'll be prompted to change your username and password. Choose a username and password, then click the Change Password button. Step 6: Go to Wireless Wireless Security, then set the same Security Mode, Algorithm, and Shared Key as your primary router. Screenshot by Ed Rhee/CNET Step 7: Go to Wireless Basic Settings, then change the Wireless Mode to Client Bridge. Set the same Network Mode and SSID as your primary router. If your bridge router is an N router, you may also need to set the same wireless channel width as your primary router.
Click Save, then Apply Settings. Screenshot by Ed Rhee/CNET Step 8: Go to Setup Basic Setup, then fill in the router IP info. For the local IP address of the router, choose an address in the same subnet as your primary router.
If your primary router is on the 192.168.1.x subnet, choose something like 192.168.1.15. Leave the Subnet Mask as 255.255.255.0 and enter the IP address of your primary router as the Gateway. Leave Local DNS blank and select your time zone. Optionally, you can check the box to Assign WAN Port to Switch. This converts the WAN port to a LAN port, providing you with an extra port on your bridge router. Click Apply Settings.
Screenshot by Ed Rhee/CNET Step 9: Log back in to your bridge router using the new address you set (192.168.1.15). Step 10: Go to Security Firewall, then under Block WAN Requests, make sure that only 'Filter Multicast' is checked.
Screenshot by Ed Rhee/CNET Step 11: Under Firewall Protection, make sure 'SPI Firewall' is disabled, then click Apply Settings. Step 12: Go to Setup Advanced Routing, then set the Operating Mode to 'Router.' Screenshot by Ed Rhee/CNET Step 13: Remove the static IP address from your computer and re-enable automatic IP addressing.
At this point, the bridge router should pass along an IP address from the primary router to your computer, giving you access to the Internet. Step 14: Once you've verified that your computer can access the Internet while physically connected to the bridge router, you can disconnect your computer.
You're now ready to connect your wired devices to the bridge router from anywhere in your home (within range of your primary router). Notes:. If you're using MAC filtering on your primary router, you'll want to add the bridge router's wireless MAC address, not the LAN MAC address that's usually printed physically on the router. To find the wireless MAC address, go to Status Sys-Info. If your primary router is a Wireless-N router, but your bridge router is a Wireless-G router, you may need to set the wireless mode to a setting that supports b/g networks.
Now you can connect all your wired devices to your wireless network, even if they're not next to your primary router. It's worth mentioning that a wireless bridge is also useful when the scenario is reversed. If you have your Internet modem and primary router next to your TV, but need connectivity to your computer in another location, you can use the wireless bridge to provide a connection to your computer, printer, NAS, etc.
. PlexAPI plugin created and maintained by OpenViX Team available via online plugin feeds. Use the tuners from your Linux Enigma 2 receiver in PlexDVR on a suitable Plex Server. For PlexAPI support please see the support section here:. If this is your first visit, be sure to check out the by clicking the link above. You may have to before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below. We may place 'cookies' on your personal computer. 'Cookies' are small identifiers sent from a website server and stored on your computer’s hard drive, similar to a license plate, that help us to recognize you if you visit this Site again.
Cookies are not designed to be used to get data from your hard drive, your email or any other personal data about you. To protect your privacy, we do not use cookies to store or transmit any personal information about you on the Internet. By using this site or dismissing this notice your are consenting to their usage. D I S C L A I M E R My right to post information is protected under the rights for freedom act. In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play.
Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it! Follow us on Twitter Rules can be found Support our sponsor World-Of-Satellite Support our sponsor VUPLUS-SHOP.CO.UK, Triax 1.1m Powered by TM2600, Technomate 80cm Powered by TM-2600 and Fixed 28.2 Zone 2 dish. D I S C L A I M E R My right to post information is protected under the rights for freedom act.
In all instances, information discussed here on my posts are either hypothetical in nature, out of general curiosity, common knowledge, public knowledge, or role-play. Any use of the collective descriptions and shared knowledge from any of my posts are at the sole discretion of the reader. I am not responsible for what you do with it! Follow us on Twitter Rules can be found Support our sponsor World-Of-Satellite Support our sponsor VUPLUS-SHOP.CO.UK, Triax 1.1m Powered by TM2600, Technomate 80cm Powered by TM-2600 and Fixed 28.2 Zone 2 dish. Quick Navigation.
Site Areas. Forums.
. PlexAPI plugin created and maintained by OpenViX Team available via online plugin feeds. Use the tuners from your Linux Enigma 2 receiver in PlexDVR on a suitable Plex Server. For PlexAPI support please see the support section here:.
If this is your first visit, be sure to check out the by clicking the link above. You may have to before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. We may place 'cookies' on your personal computer.
'Cookies' are small identifiers sent from a website server and stored on your computer’s hard drive, similar to a license plate, that help us to recognize you if you visit this Site again. Cookies are not designed to be used to get data from your hard drive, your email or any other personal data about you. To protect your privacy, we do not use cookies to store or transmit any personal information about you on the Internet. By using this site or dismissing this notice your are consenting to their usage. Introducing the Open Media WIFI Bridge This device allows you to connect any fixed wired network device to your wireless network. It Supports WEP (64 bit), WEP (128 bit), WPA, WPA2 security.
Related stories. Possible solutions include, dedicated wireless adapters for each device, or installing Ethernet jacks. Unfortunately, those options can get expensive and each has its unique drawbacks. Another option is using a wireless bridge. A wireless bridge connects two wired networks together over Wi-Fi. The wireless bridge acts as a client, logging in to the primary router and getting an Internet connection, which it passes on to the devices connected to its LAN Jacks.
You can buy a dedicated wireless bridge, but if you have an old router lying around, you might be able to convert it into a wireless bridge using DD-WRT. A wireless bridge connects two wired networks together over Wi-Fi. Screenshot by Ed Rhee/CNET. Is free Linux-based firmware for routers that replaces the router's factory firmware.
It can breathe new life into an old router, giving it enhanced performance and new features. One of the features of DD-WRT is the ability to switch the router's function to a wireless bridge. This tutorial, based on the, will go over how to configure DD-WRT for use as a wireless bridge (client bridge mode), using a Linksys WRT54G router as an example.
The process is fairly straightforward but will require some time and patience to complete. Alawar crack download. In the steps below, primary router refers to the main router that you'll connect to, while bridge router refers to the router you're configuring as a client bridge.
Step 1: Check the to see if your router is supported. If your router isn't supported, keep an eye out at for router deals. Rick Broida recently found a. Step 2: If your router is supported, you'll see it listed in the database and it'll include links to the firmware. It may also include device-specific directions on how to install DD-WRT, but you'll want to read over the as well. In some cases, you'll need to install a firmware prep, prior to installing the actual DD-WRT firmware.
It's possible to brick your router during installation if not performed correctly, so read the directions carefully and follow each step as noted. Step 3: Once you've successfully installed DD-WRT, perform a hard reset on the router. This usually involves holding a reset button/pin for 30 seconds or until you see the router's lights flashing. Refer to your router's user manual to figure out the exact method for a hard reset. Step 4: Connect an Ethernet cable from your computer to one of the LAN jacks on the bridge router, then set a static IP address on your computer.
Use something like 192.168.1.10, so you'll be on the same subnet as the bridge router, which will have an IP address of 192.168.1.1. Step 5: Open a Web browser and enter 192.168.1.1 in the address bar. The DD-WRT Web interface will appear and you'll be prompted to change your username and password. Choose a username and password, then click the Change Password button.
Step 6: Go to Wireless Wireless Security, then set the same Security Mode, Algorithm, and Shared Key as your primary router. Screenshot by Ed Rhee/CNET Step 7: Go to Wireless Basic Settings, then change the Wireless Mode to Client Bridge. Set the same Network Mode and SSID as your primary router. If your bridge router is an N router, you may also need to set the same wireless channel width as your primary router. Click Save, then Apply Settings. Screenshot by Ed Rhee/CNET Step 8: Go to Setup Basic Setup, then fill in the router IP info. For the local IP address of the router, choose an address in the same subnet as your primary router.
If your primary router is on the 192.168.1.x subnet, choose something like 192.168.1.15. Leave the Subnet Mask as 255.255.255.0 and enter the IP address of your primary router as the Gateway. Leave Local DNS blank and select your time zone. Optionally, you can check the box to Assign WAN Port to Switch. This converts the WAN port to a LAN port, providing you with an extra port on your bridge router.
Wifi Bridge Access Point
Click Apply Settings. Screenshot by Ed Rhee/CNET Step 9: Log back in to your bridge router using the new address you set (192.168.1.15). Step 10: Go to Security Firewall, then under Block WAN Requests, make sure that only 'Filter Multicast' is checked. Screenshot by Ed Rhee/CNET Step 11: Under Firewall Protection, make sure 'SPI Firewall' is disabled, then click Apply Settings.
Wireless Media Bridge
Step 12: Go to Setup Advanced Routing, then set the Operating Mode to 'Router.' Screenshot by Ed Rhee/CNET Step 13: Remove the static IP address from your computer and re-enable automatic IP addressing. At this point, the bridge router should pass along an IP address from the primary router to your computer, giving you access to the Internet. Step 14: Once you've verified that your computer can access the Internet while physically connected to the bridge router, you can disconnect your computer. You're now ready to connect your wired devices to the bridge router from anywhere in your home (within range of your primary router). Notes:. If you're using MAC filtering on your primary router, you'll want to add the bridge router's wireless MAC address, not the LAN MAC address that's usually printed physically on the router.
To find the wireless MAC address, go to Status Sys-Info. If your primary router is a Wireless-N router, but your bridge router is a Wireless-G router, you may need to set the wireless mode to a setting that supports b/g networks. Now you can connect all your wired devices to your wireless network, even if they're not next to your primary router. It's worth mentioning that a wireless bridge is also useful when the scenario is reversed.
If you have your Internet modem and primary router next to your TV, but need connectivity to your computer in another location, you can use the wireless bridge to provide a connection to your computer, printer, NAS, etc.
I always wanted to try one of this adapters. This is a wifi network interface that connects to the Ethernetport. So, if you have a device that do not have Wifi and only have Ethernet, you can use one of this to connect this device to a Wifi access point. This can be usefull for devices like TVs, Xbox, Ethernet only printers, old ethernet computers, or even for OS/2-eComStation when you don't have a wifi adapter driver for it. So I got this VAP11G at ebay for $17 to try it out. Drivers Please notice that the application (since it is not a driver after all) are only required to configure the device and set the SSID specs.
After that to make it work, you just need to plug it into the ethernet port of the device that is required to be connected to the wifi network. Links Official Site: Configuration You need to configure this device first to put the SSID and the password. Once it is configured you can take it to any other device with Ethernet port to try it out. To configure it you need to install the 'VAP11G Setup' software that came with the adapter. This software also uses 'WinPCap' to make a bridge with the adapter in Windows and allow you to configure it. Windows 8 (64 bits) Require: and: After installing the requirements the VAP11g Wifi Bridget Configuration tools works fine. It found the network adapter It found all wifi networks on the area Allowed to put the password on it.
Vonets Wifi Bridge Software
After that the VAP11G green light started to flash. Windows 7 Not tried yet. Windows XP I was able to configure the device using Windows XP. WinPCap and VAP11G run fine under this OS. I was able to configure the wifi network with VAP11G and I got it read to make it work with a local ethernet only printer and also with a PC with eComStation The printer and PC worked fine. They both were able to connect to the wifi via the ethernet port. Related Project:.
I found this python project with the goal to configure the device from any platform.